Pressure altitude calculator
Find the air pressure at any altitude, a field's pressure altitude from its altimeter setting, or density altitude from the temperature and dew point. The results use the National Weather Service formulas, and the nearest airport's latest report can fill in the numbers for you.
Pressure at altitude
At 5,280 ft (1,609 m), the standard atmosphere gives 24.63 inHg (834.2 hPa), 82% of the sea-level pressure. Standard temperature there is 40 °F (5 °C).
On a real day the weather moves this up or down; an unadjusted barometer at that height reads close to it.
Worked examples:
- Pressure altitude at Denver International (5,433 ft) with an altimeter setting of 30.00 inHg: 5,351 ft.
- Density altitude at Denver International on a 95 °F afternoon (dew point 40 °F, altimeter 30.00 inHg): 8,889 ft.
By Marko Visic, BSc Physics. Reviewed November 17, 2026.
Pressure altitude is the height in the standard atmosphere where the pressure equals the pressure you have now. The National Weather Service computes it as 145,366.45 × [1 − (P ÷ 1013.25)^0.190284] feet, with P the station pressure in hPa. Pilots use a shortcut: field elevation plus 1,000 feet for every inch of mercury the altimeter setting sits below 29.92.
- Field elevation 5,433 ft
- Pressure altitude 5,350 ft
- Density altitude 8,890 ft (hot afternoon: 95 °F)
On this page
Air pressure at altitude
Air pressure falls as you climb because there's less air above you. In the standard atmosphere that weather services and pilots use as a reference, pressure drops by about 1 inch of mercury for every 1,000 feet up to 10,000 feet, the FAA says. Above that it falls more slowly.
18,000 ft
About where the standard atmosphere's pressure falls to half its sea-level value: 14.94 inHg (505.8 hPa), against 29.92 inHg (1013.25 hPa) at sea level.
Source: National Weather Service pressure-altitude formula
Table: air pressure at altitude in the standard atmosphere
| Altitude | Pressure | Share of sea-level pressure | Standard temperature |
|---|---|---|---|
| 0 ft (0 m) | 29.92 inHg 1013.3 hPa | 100% | 59 °F (15 °C) |
| 1,000 ft (305 m) | 28.86 inHg 977.2 hPa | 96% | 55 °F (13 °C) |
| 2,000 ft (610 m) | 27.82 inHg 942.1 hPa | 93% | 52 °F (11 °C) |
| 3,000 ft (914 m) | 26.82 inHg 908.1 hPa | 90% | 48 °F (9 °C) |
| 4,000 ft (1,219 m) | 25.84 inHg 875.1 hPa | 86% | 45 °F (7 °C) |
| 5,000 ft (1,524 m) | 24.89 inHg 843.0 hPa | 83% | 41 °F (5 °C) |
| 6,000 ft (1,829 m) | 23.98 inHg 811.9 hPa | 80% | 38 °F (3 °C) |
| 7,000 ft (2,134 m) | 23.09 inHg 781.8 hPa | 77% | 34 °F (1 °C) |
| 8,000 ft (2,438 m) | 22.22 inHg 752.5 hPa | 74% | 30 °F (−1 °C) |
| 9,000 ft (2,743 m) | 21.39 inHg 724.2 hPa | 71% | 27 °F (−3 °C) |
| 10,000 ft (3,048 m) | 20.57 inHg 696.7 hPa | 69% | 23 °F (−5 °C) |
| 11,000 ft (3,353 m) | 19.79 inHg 670.1 hPa | 66% | 20 °F (−7 °C) |
| 12,000 ft (3,658 m) | 19.03 inHg 644.3 hPa | 64% | 16 °F (−9 °C) |
| 13,000 ft (3,962 m) | 18.29 inHg 619.3 hPa | 61% | 13 °F (−11 °C) |
| 14,000 ft (4,267 m) | 17.57 inHg 595.1 hPa | 59% | 9 °F (−13 °C) |
| 15,000 ft (4,572 m) | 16.88 inHg 571.7 hPa | 56% | 6 °F (−15 °C) |
| 18,000 ft (5,486 m) | 14.94 inHg 505.8 hPa | 50% | −5 °F (−21 °C) |
| 20,000 ft (6,096 m) | 13.75 inHg 465.5 hPa | 46% | −12 °F (−25 °C) |
| 25,000 ft (7,620 m) | 11.10 inHg 375.8 hPa | 37% | −30 °F (−35 °C) |
| 29,032 ft (8,849 m)Everest | 9.28 inHg 314.2 hPa | 31% | −45 °F (−43 °C) |
| 30,000 ft (9,144 m) | 8.88 inHg 300.7 hPa | 30% | −48 °F (−44 °C) |
| 35,000 ft (10,668 m) | 7.04 inHg 238.3 hPa | 24% | −66 °F (−54 °C) |
Calculated with the National Weather Service pressure-altitude formula.
These are standard-atmosphere values. On a real day the weather moves the pressure at any height up and down around them, which is why the calculator's second and third tabs start from an actual altimeter setting.
Phones can work the other way round. Android's developer documentation describes how an app turns a phone's pressure reading into an altitude: it needs the sea-level pressure at the same moment, which the documentation says can usually be retrieved from airports nearby. Each city page shows its nearest airport's altimeter setting, the sea-level number to use for this, and the calculator's first tab does the same calculation.
The pressure altitude formula
Pressure altitude is what an altimeter reads when it's set to 29.92 inches of mercury. The FAA lists three ways to find it: set the altimeter to 29.92 and read it, correct the indicated altitude for the reported altimeter setting, or use a flight computer such as an E6B. The National Weather Service formula does the same job from station pressure, with P in hPa:
An airport reports its altimeter setting, not its station pressure, so the calculator first converts the altimeter setting back to station pressure with the National Weather Service altimeter-setting formula, the one sea-level pressure explains, and then applies the formula above.
How close the pilots' shortcut gets
The shortcut adds 1,000 feet to the field elevation for every inch of mercury below 29.92 and subtracts it for every inch above. For altimeter settings from 29.00 to 30.80 inHg it stays within about 70 feet of the formula, at sea level as well as at Denver International or a 10,000-foot field.
Table: the pilots' shortcut against the NWS formula at Denver International (5,433 ft)
| Altimeter setting | NWS formula | Pilots' shortcut | Difference |
|---|---|---|---|
| 29.00 inHg | 6,286 ft | 6,353 ft | +67 ft |
| 29.50 inHg | 5,815 ft | 5,853 ft | +38 ft |
| 29.92 inHg | 5,425 ft | 5,433 ft | +8 ft |
| 30.30 inHg | 5,075 ft | 5,053 ft | −22 ft |
| 30.80 inHg | 4,621 ft | 4,553 ft | −68 ft |
Formula: National Weather Service. Shortcut: 1,000 ft per inch of mercury from 29.92 (FAA Aeronautical Information Manual).
The density altitude formula
Density altitude is "pressure altitude corrected for nonstandard temperature", in the FAA's words: the height in the standard atmosphere where the air would be as thin as it is now. Warm air is thinner than standard, so on a hot day an airport's density altitude can sit thousands of feet above its elevation.
The National Weather Service computes it in three steps. First the vapor pressure e, in hPa, from the dew point Td in °C:
Then the virtual temperature Tv, the temperature dry air would need to be as thin as the moist air, from the air temperature T in kelvins and the station pressure P in hPa:
Then density altitude in feet, with the station pressure in inHg and Tv converted to degrees Rankine:
Take Denver International, 5,433 feet up, on a 95 °F afternoon with a 40 °F dew point and an altimeter setting of 30.00 inHg. Its pressure altitude is about 5,350 feet, and its density altitude about 8,890 feet. With a 65 °F dew point instead and nothing else changed, the density altitude comes out about 190 feet higher.
The FAA treats humidity as a small correction: it notes that humidity "is not generally considered a major factor in density altitude computations", and suggests adding 10 percent to the computed takeoff distance when the air is humid.
- Standard: 59 °F at sea level (dots closer together).
- Hot: fewer molecules in the same space.
Why pilots watch density altitude
In its density altitude guide the FAA says takeoff distance, power available in normally aspirated engines and climb rate "are all adversely affected": the takeoff run gets longer and the climb gets slower. Takeoff charts start from pressure altitude and temperature for that reason.
3,500 ft
On a 95 °F afternoon at Denver International (5,433 ft, altimeter 30.00 inHg, dew point 40 °F), density altitude comes out at about 8,890 ft: the airplane performs as if the field sat about 3,500 feet higher.
Source: calculated with the National Weather Service density-altitude formula
Denver International right now
Denver International
Measured at , at an elevation of 5,433 ft (1,656 m).
| Altimeter setting | Temperature | Dew point | Pressure altitude | Density altitude |
|---|---|---|---|---|
| 29.88 inHg 1011.9 hPa | 45 °F (7 °C) | 20 °F (−7 °C) | 5,462 ft (1,665 m) | 5,889 ft (1,795 m) |
Density altitude is 456 ft above the field right now.
NOAA Aviation Weather Center METAR report for KDEN. Pressure altitude and density altitude calculated with the National Weather Service formulas.
How to read the results
- Pressure at altitude gives the standard-atmosphere pressure at the height you enter, its share of the sea-level value and the standard temperature there. A barometer that isn't set to sea level reads close to it on an ordinary day.
- Pressure altitude is what an altimeter set to 29.92 would read at the field. It sits above the field elevation when the altimeter setting is below 29.92 inHg and below it when the setting is higher, by roughly 1,000 feet per inch. The result also shows the pilots' shortcut next to the formula, and the station pressure the calculator worked from.
- Density altitude starts from pressure altitude and adds the effect of temperature and humidity. A result above the field elevation means thinner air than standard, which the FAA links to longer takeoff runs and slower climbs.
Ways to use the calculator
Check a hot-day departure. Enter the field elevation, the altimeter setting, the temperature and the dew point, or press "Use the nearest airport". Your aircraft's performance charts start from pressure altitude and temperature, and the density altitude shows at a glance how far the day is from standard. The official weather briefing and the aircraft's own charts still have the final word.
Sanity-check a phone's altitude. In "Pressure at altitude", choose "Pressure → altitude", then enter the phone's pressure reading and the nearest airport's altimeter setting. If the phone shows a very different altitude, it's probably working from an old or standard sea-level value.
Know what an unadjusted barometer should read. The first tab gives the standard pressure at your home's height, which is roughly what a barometer reads there before it's set to sea level. How to read a barometer explains how to set it.
Questions people ask
What is pressure altitude?
The altitude in the standard atmosphere where the pressure equals the station's pressure right now. It's what an altimeter reads when it's set to 29.92 inHg, and it's the starting point for aircraft performance charts.
How do you calculate pressure altitude?
Convert the altimeter setting to station pressure, then apply the National Weather Service formula: 145,366.45 × [1 − (P ÷ 1013.25)^0.190284] feet, with P in hPa. As a shortcut, add 1,000 feet to the field elevation for every inch of mercury the altimeter setting is below 29.92.
Is pressure altitude the same as density altitude?
No. Pressure altitude adjusts only for pressure. Density altitude also adjusts for temperature and humidity, so on a hot day it's higher than the pressure altitude.
How do you calculate density altitude?
From the station pressure, the temperature and the dew point, with the three National Weather Service formulas above: vapor pressure, then virtual temperature, then density altitude. The calculator's third tab runs all three.
Does humidity affect density altitude?
Yes, a little. Moist air is lighter than dry air at the same temperature and pressure. In the Denver example above, raising the dew point from 40 °F to 65 °F adds about 190 feet.
What is the air pressure at 10,000 feet?
In the standard atmosphere, 20.57 inHg (696.7 hPa), about 69 percent of the sea-level value. The day's weather moves the real figure up or down.
How do you find pressure altitude on an E6B?
The FAA lists a flight computer as one of three ways to find it, next to setting the altimeter to 29.92 or correcting the indicated altitude for the reported altimeter setting. The calculator above works it out from the field elevation and the altimeter setting.
Can you calculate altitude from barometric pressure?
Yes, if you know the sea-level pressure at the same time. Android's developer documentation describes it that way, with the phone's pressure sensor and the sea-level pressure from nearby airports. Enter your reading and the nearest airport's altimeter setting in the calculator's first tab.
Sources
- National Weather Service, pressure-altitude formula — pressure at altitude and pressure altitude
- National Weather Service, density altitude formula — vapor pressure, virtual temperature and density altitude
- National Weather Service, altimeter setting formula — station pressure from the altimeter setting
- FAA, Pilot's Handbook of Aeronautical Knowledge, chapter 11 — standard atmosphere, ways to find pressure altitude, density altitude
- FAA, Density Altitude (FAA-P-8740-2) — effects on takeoff and climb, humidity
- Android Developers, SensorManager.getAltitude — altitude from a phone's pressure sensor
- NOAA Aviation Weather Center, METAR reports — Denver International live
- FAA, Aeronautical Information Manual, 7-2-3 Altimeter Errors — 1,000 feet per inch of mercury
- NIST Special Publication 811, Appendix B — unit conversions